EU Emissions Rules
Yuna
| 20-11-2026
· Automobile team
Europe's automotive industry is approaching an important change in how vehicle emissions will be regulated through 2035. On 4 November 2026, the European Parliament's Environment Committee supported a proposal to ease several CO₂ requirements for passenger cars and light commercial vehicles.
The proposal includes a 95% emissions reduction target for new cars, revised targets for vans and additional credits for manufacturers using climate-friendly steel produced in Europe. The decision follows earlier votes by the Industry and Transport Committees.

A Different Target for Passenger Cars

Under the proposal, manufacturers would need to reduce the average CO₂ emissions of their new passenger cars by 95% by 2035, compared with 2021 levels. This would replace the previous 100% reduction target. An additional credit of up to 7.5 percentage points could be available to manufacturers using climate-friendly steel produced in Europe. If the maximum credit were applied, the required reduction could effectively fall to 87.5%.
The credit system is intended to recognise the environmental contribution of materials used in vehicle production. Rather than measuring vehicle emissions alone, the proposal also considers how manufacturing choices can contribute to the overall reduction target. The approach would leave room for new combustion-engine and hybrid vehicle registrations after 2035, provided manufacturers meet the applicable fleet requirements.

Vans Would Receive Separate Targets

Light commercial vehicles would follow a different timetable. For 2030, the proposal sets a CO₂ reduction target of 35% compared with 2021 levels. This is less demanding than the 40% reduction included in the European Commission's earlier draft and the 50% requirement under the existing regulations described in the report.
The 2035 target for vans would also change. Instead of requiring a 100% reduction, the proposal would set the figure at 80%. Manufacturers could receive an additional credit of up to 7.5 percentage points for using qualifying low-CO₂ steel, following the same general approach proposed for passenger cars. According to the proposal's supporters, the revised targets would allow some new combustion-engine and hybrid vans to remain available beyond 2035.

Steel Credits Before 2035

The proposal also addresses how quickly manufacturers could begin receiving credits for low-CO₂ steel. For the period between the revised regulation entering into force and the end of 2034, the maximum credit discussed is three percentage points. The larger allowance of up to 7.5 percentage points would apply under the proposed framework from 2035.
This gradual approach gives manufacturers an opportunity to incorporate lower-emission materials into their production processes before the main 2035 targets take effect. The steel provision is an important distinction between the proposed framework and the European Commission's original draft. The earlier version set a 90% reduction target for 2035, equivalent to average fleet emissions of 11 grams of CO₂ per kilometre, rather than zero grams.

How the Committee Votes Went

The Environment Committee adopted the proposal on 4 November with 48 votes in favour, 30 against and two abstentions. Earlier, the Industry Committee had supported it with 49 votes in favour, 27 against and five abstentions. The Transport Committee recorded 27 votes in favour, 18 against and one abstention.
Together, the three committee decisions indicate support for changing the existing emissions framework. However, they do not represent final approval of the complete package.

What Happens Before the Final Decision?

The next major step is the full European Parliament's plenary session, scheduled for December. If the Parliament approves the package, it must then proceed through the Council of the European Union, where member states will consider the proposal. The process may still lead to further amendments. Different groups and interested organisations can seek changes before the final rules are agreed, so the current figures should be understood as proposed targets rather than settled requirements.
The European Commission's Auto Package, presented at the end of 2025, provides the broader framework for these changes. Its final form will determine how the revised targets, material credits and vehicle technology provisions work together.
The Environment Committee's decision marks another step towards revising Europe's vehicle emissions framework. The proposed 95% reduction target for passenger cars, 80% target for vans and credits for low-CO₂ steel would give manufacturers more flexibility in meeting future requirements.
However, the proposal still needs approval from the full European Parliament and the Council. Until those steps are completed, the final targets and conditions may change. For carmakers, the coming decision will be important in planning future vehicle ranges, production methods and material choices.